Adhesive Chain Lubricant is highly tenacious with excellent resistance to water and high temperature, it provides maximum protection from wear due to twisting, bending, stretching, as well as protection from moisture, dust and corrosive environment It drives deep into tight inaccessible areas with good penetration at low temperature and has good mechanical stability.
High Temperature Chain Oil is a synthetic lubricant with additives to provide enhanced oxidation stability, wear protection and corrosion protection. It leaves no residue and extends re-lubrication intervals.
These properties combine to give substantial reduction in power consumption, overall reduction in frictional losses, in turn lowering operating temperatures and extending parts life and lengthened lubricant life.
Lubricating chains, wire ropes, stentor frames, conveyors in ceramic tile plants, conveyors in varnish curing plants etc.
KF-150/220/320 series is a synthesized hydrocarbon lubricant with additives to provide enhanced oxidation stability, wear protection, corrosion protection and load carrying abilities at extreme pressure conditions, specifically developed for gears and bearings. It exhibits low traction co-efficient and high viscosity index. These properties combine to give substantial reduction in power consumption, overall reduction in frictional losses, in turn lowering operating temperatures and extending parts life and lengthened lubricant life.
KF-SPIN series oils are synthetic, low viscosity lubricants exhibiting Anti-wear, Anti-corrosive, Anti-foaming properties.
Low volatility, Low co-efficient of friction, High oxidative stability, Significant increase in oil drain intervals..
Textile Ring frame spindles, TFO’s, Timing Gears Hydraulic system of high precision tools etc.
KF-150/220/320 series is a synthesized hydrocarbon lubricant with additives to provide enhanced oxidation stability, wear protection, corrosion protection and load carrying abilities at extreme pressure conditions, specifically developed for gears and bearings. It exhibits low traction co-efficient and high viscosity index. These properties combine to give substantial reduction in power consumption, overall reduction in frictional losses, in turn lowering operating temperatures and extending parts life and lengthened lubricant life.
KF-COM 2000 Series Polyol Ester based compressor lubricant specifically designed to provide long term lubrication in Screw, reciporcating and process gas compressors.
* Fewer oil changes.
* Lower oil consumption
* Reduces compressor maintenance
* Eliminates lacquering (varnish) and deposits
* Greatly reduces fire and explosion hazard
* Reduces energy consumption
* Separates water condensate rapidly
For cylinder and frame lubrication of reciprocating compressors and vacuum pumps using the following gases: Air Carbon Dioxide (dry) Hydrogen Sulphide (dry) Propane,Butadiene Ethylene Natural,Gas Synthesis Gas,Carbon Monoxide Helium Methane Sulphur Hexafluoride
Furnace (crack) Gas, Hydrogen ,Nitrogen and HFC 134A.
Nominal Operating Range is –30°C to 240°C
| KF-COM2032 | KF-COM2068 | KF-COM2220 | |
|---|---|---|---|
| Viscosity @ 40 o C ,cSt | 32-36 | 66-68 | 220-226 |
| Flash Point o C | 246 | 266 | 274 |
| Pour Point o C | <- 57 | - 48 | - 30 |
| Viscosity Index | 140 | 148 | 178 |
Shelf Life : 24 months
Packing : 20, 50 & 200 ltrs Drum
The following seals, paints, and plastics are recommended for use in contact with KF-COM 2000 SERIES Lubricants. Materials not recommended are also shown.
RECOMMENDED - Viton, High Nitrile Buna N, Teflon, Epoxy Paint, Oil-Resistant Alkyd, Nylon, Delrin, Celcon, and PBT.
NOT RECOMMENDED - Neoprene, SBR Rubber, Low Nitrile Buna N, Acrylic Paint, Lacquer, Polystyrene, PVC and ABS.
1.High viscosity index and low volatility, provides an effective lubricant film under condition of high temperature and high stress
2.Low temperature properties permits startup at sub zero temperatures
3.The high level of thermal stability make extended service a feasible benefit
4.Compatibility with conventional sealants and paints
5. Low vapour pressure, Low volatility and High Flash point.
| Appearance | Clear and Homogeneous |
|---|---|
| Viscosity @ 40 o C ,cSt | 84 to 90 |
| Viscosity@100 o C cSt | 9 to 10 |
| Viscosity Index | 145 |
| Flash Point o C | 276 (COC) |
| Density | 0.84 to 0.86 |
| Pour Point o C | -40 o C |
| PShelf Life | 36 months |
| Packing | 20 & 200 litres drum |
Caution: To the best of our knowledge, this technical data is true and accurate at the date of issuance but is subject to change without prior notice. Liability, if any, is limited to the replacement of an equivalent amount of new product or refund of the purchase price. This warranty specifically excludes labour or cost of labour.
These favorable properties include:
A wide operational temperature range.
Good viscometrics (high viscosity index).
Thermal Stability.
Oxidative Stability.
Hydrolytic stability.
*
Shear stability.
Low corrosivity.
Compatibility with mineral oils.
Compatibility with various materials of construction.
Low toxicity.
compatibility is an important factor for any lubricant. Unlike mineral oils,KF-VAC 10 does not have a tendency to swell elastomeric materials. In a test of a KF-VAC10 vs. a mineral oil for seal compatibility, four seal materials were studied: acrylate, silicone, nitrile and fluoroelastomer. The seals were evaluated at the end of the test for changes in tensile strength, elongation, volume (seal swell), and hardness. KF-VAC 10 performance fell within the specification limits for all four elastomers. The mineral oil failed with silicone.
1.Ammonia
2.Freon 11, 12
3.134A
4.Nitrogen
5.Soluble in hydrocarbon solvents
INCOMPATIBLE
1.Chlorates
2.Nitrates
3.Peroxides
4.Oxidising Agents